followers 0 popularity
0
following 1

following  view all

Groups
routerloginsupport is not in any groups

Interests

Routerlogin.net is the only available login portal for Netgear Router Login. But most of the users face failures for Netgear Router Login using Routerlogin.net. Or each time they’re redirected to a webpage where there is no space for Netgear Router Login. These are the common issues faced by most of the users when they try to access the rotuerlogin.net or 192.168.1.1 IP for their Netgear router login. And as a result of this, they were unable to get the login access. The main cause for this is that the users are committing some common mistakes while setting up their Netgear Router. But now you need not worry.
routerloginsupport

Process to Set up a Netgear router for AT &T users

Apr 8th 2019 at 2:59 AM

 

 

It only takes about 15 minutes to configure your Netgear router to work with the Internet service that you get through your AT & T DSL cable, create a local area network and provide Internet access to the wired and wireless devices. Record the wireless network IDs and passwords as you configure them, because you can enable up to four different wireless networks on a single Netgear router setup- a personal network and a guest network on both the 2.4 GHz and 5 GHz frequencies.

Give below are the instructions for the Setup.


Connection of devices

Turn off the AT & T DSL modem. Connect one end of the Ethernet cable that came with the Netgear router to the Ethernet port on the DSL modem. Connect the other end of the cable to the WAN port of the router, which is the Ethernet port that is colored yellow or red.

Connect one end of the other Ethernet cable to one of the four Ethernet LAN ports of the router to the computer or laptop you must use to configure the router.

Turn on your AT & T modem and wait a minute. Turn on the Netgear router and then turn on or restart the system and log in to your computer.

Means To Configure Router

Launch a browser, type "www.routerloginnet.net" in the address bar and press" Enter "to start the genius Netgear and configure your router.

  • Type "admin" in the username symbol, type "password" in the password box, and then click "OK" to log in to the router. Select "Yes" and follow the instructions on the screen if the router asks you to update the router with the new firmware.

  • Select "Internet" from the home screen and select "Yes" to indicate that AT & T requires a login. Enter your AT & T DSL username and password in the fields provided. Accept the default settings for the rest of the Internet settings and click "Apply." Click on "Test", after the router restarts to view the NETGEAR website through your AT & T Internet connection.

  • Select "Wireless" on the genie home screen and set up the 2.4 GHz wireless network in the, or low band, frequency. Enter a name that users see when browsing the available 2.4 GHz wireless networks in the Name (SSID) field. Select the WPA2-PSK [AES] WPA-PSK as the security mode. Enter a password of eight to 63 characters that a user types in their wireless device to access their local area network.

  • For enabling the wireless guest network, check the box stating- Enable guest network. Click to check "Enable Wireless Isolation" and prevent clients from accessing the devices or resources of each one in your network.

  • Enter a name that appears when users are browsing available wireless networks. Select the same wireless security method that you used for the local network but write a password different from eight to 63 characters for guests to use when connecting to the network. Click "Apply" to save the guest network settings.

Configuring the Local Area Network

After the Netgear Router Installation, repeat the previous two steps to configure a local area network and a guest network in the 5 GHz, or high band, frequency.

Check that you can successfully connect to the Internet with a wireless device in your area network and your accompanying local network in both the low and high band of the frequency band.

Select "Advanced" from the home screen, select "Administration" and then "Set password" to assign a new password to the router configuration screens.

Type password as the old password and type a new password twice in the fields on the screen. Click on "Enable password recovery," type two sets of password recovery questions and answers, and click "Apply" to save the changes.

Re-enter the configuration wizard at Netgear router default login using "admin" as the user name and the new password you just assigned. Choose the remaining menu options and follow the instructions on the screen to activate and configure as appropriate.

Tips and warnings

If you only have low band or high band devices and do not want a guest network, you only need to set up a wireless network on the router.

AT & T is not compatible with the non-AT & T routers provided. If the AT & T modem is also a router or gateway with the functionality enabled, disable it by setting the device as a bridge. Consult the resources for more information.

 

 

0 comments
Please to comment

sign in

Username
Password
Remember Me


New to IM faceplate? join free!

Lost Password? click here