followers 1 popularity
following 1

followers  view all

following  view all

mikuka is not in any groups

Laser line always takes the lowest time consumption

Dec 8th 2015 at 3:39 AM
Laser line always takes the lowest time consumption

When users are fallen into difficult to make high accuracy and high precision line positioning, the selection of laser line generator is always a quite nice recommendation for users for all working fields efficiently. On condition that users are selecting this accessory line, it is merely used separately, but always using together with machine or devices.

On basis of high brightness laser beam emission from its internal red, blue, blue violet or green laser diodes, line laser alignment tool is always making sure of high brightness reference line generation. No matter close distance or long distance line targeting, users are always able to get high efficiency line projection on all desired working surfaces efficiently.

In a large variety of industrial machinery processing work fields, laser line generator might be used for precise line positioning and line cutting on various raw materials. For instance, it can be used by garment makers to make line positioning on cloths in garment production lines. For instance, garment makes would prefer to choose high brightness line laser alignment tool to make accurate line targeting on cloths. Laser line always takes the lowest time consumption, only according to very easy installation on heat transfer machine or laser alignment for screen printing work etc, alignment laser line is highly bright and visible.

How to Turn a Cheap Laser Pen Into a Burning Laser
A laser pen can be great fun whether you're using it to give your pets exercise or to annoy people at the movie theater. By following a few simple steps, you can increase the power of your laser pen, allowing it to pop balloons and light matches. This can be a good way to learn about electronics and optics.



Remove the battery or batteries.
Unscrew or pry off the housing.
Locate the variable resistor on the circuit board. It will be a tiny platform connected to the circuit board by two prongs. In the center of the platform will be a circular area. There will be a divot in the center of this area.

Insert the tip of the screwdriver into the divot and turn it slightly counterclockwise.
Assemble the housing and reinsert the battery or batteries.Turn on the laser. If the light is not brighter, disassemble the pen again and turn the resistor clockwise.

As with any laser, do not point it into the eyes of any person or animal.
Do not give laser pens to children.
Do no turn the resistor too far or you will burn out the laser.



Please to comment
Aug 3rd 2016 at 12:51 AM by chanyuan
This post/comment has been removed due to violations of our terms of use.

Laser line always takes the lowest time consumption

Dec 9th 2015 at 1:13 AM
Laser line always takes the lowest time consumption


I am not sure if it is a correct choice to get ideal dot positioning result with a high brightness Laser pointer Green 3000mw , however, it is the most practical used dot measuring tool that is widely used in a large variety of various industrial work fields.

On condition that users are making selection of wide output power of 50mW to 100mW, this advanced dot laser alignment is always generating high brightness blue dot projection on all desired working surfaces efficiently. Without a lot of time consumption of prior dot positioning, laser dot alignment is not only time saving, but also efficient enough to generate high precision dot alignment on all desired working surfaces efficiently.

Laser dot alignment application is always not the same as manual dot measurement with a sticker, laser pointer or others. It might be workable for all kinds of industrial dot alignment work, such as laser marking, laser engraving etc. On basis of the most advanced 445nm blue laser diode as its dot emission source, laser dot always keeps high brightness. Comparing with other visible lasers, this advanced laser diode module always gets higher output power of 50mW to 100mW. As a result, it is always workable for all kind of high lighting occasions and long work distances.

If you would like more information about laser pointer, please click on the Business pinterest:

In order to get high concentricity dot positioning result, 445nm blue laser diode module is cautiously designed with adjustable focus. In front part of dot laser, users can make quite simple screw of laser head part, thus getting high level of laser beam focus. Although users are required to make dot projection at quite long work distance, the adjustable focus design is able to help users get different size blue reference dot on all working surfaces.

Solder the longer of the two pins attached to the laser diode to the center hole in the incandescent bulb socket. Let the solder cool for a minute.Solder the other, short pin attached to the laser diode to the metal ring surrounding the center hole in the incandescent bulb socket. Let the solder cool for a minute.

Return the incandescent bulb socket into the disposable flashlight. Screw on the reflector.Aim the laser pointer you have made at a far wall. Depress the "on" button to project a beam of red laser light at the wall.

If you would like more information about our company advice, please click on the link:

Please to comment

sign in

Remember Me

New to IM faceplate? join free!

Lost Password? click here